While the tank was off ……

Aprilia Caponord ETV1000 Rally-Raid fuel pump harness (AP8124664) connector SupersealI finally got around to changing out the open-to-air 4-way connector that feeds the fuel pump and fuel level sensor. In went a nice 4-way Superseal (14A rated) with the connectors crimped, soldered and given a light coat of dielectric grease before sliding home into the waterproof housing.

Hopefully no more erratic fuel level due to oxidation on the pins! While I was at it I pulled the spare fuel pump harness (AP8124664) out of its bag and changed its connector as well. I’d look mighty foolish if I’d pulled that out of my spares kit at the roadside and the connectors didn’t match!

Aprilia Caponord ETV1000 Rally-Raid fuel pump harness (AP8124664) connector SupersealWhile under the hood, I noticed that the outer coat of the fuel return line (marine-grade ISO 7840 A1) is showing signs of deterioration and kinking near the swaged end at the fuel tank. I’d noticed it back in September, but unfortunately it appears to be a little worse now. Time then to order a new cLCD 170-04 1/4″ barbed quick release connector from Tom Parker (UK) along with suitable Oetiker clamps – I’ll only use clamps that need to be crimped, never ones with screws that can work loose. I’ve no problem doing the return hoses myself, but when it comes to the high pressure side, I leave it to the professionals. Last time that was MF Hydraulics in Oxford and I’ll be happy to use them again come the day.

Aprilia Caponord ETV1000 Rally-Raid fuel pump return line hoseThe marine hose has lasted well (9 years) and that’s to be expected given that hose for marine applications has to meet very strict guidelines, however I think hose rated at SAEJ30R9 with its improved impermeability and tolerance to Ethanol is probably better suited on the Capo nowadays. Either way I wouldn’t lose any sleep over it! The high pressure line and main return line are holding up just fine with no sign of wear or deterioration.

Magnecor KV85 HT leads – Review

Aprilia Caponord ETV1000 Rally-Raid Magnecor KV85 2530 HT leadsThe modified HAAS coils have been on now for just over six months and 12,000 miles and everything is ticking along just fine. Even so, the Capo needs a few treats every now and again, so I thought a nice new set of HT leads might complement the new(ish!) coils. Besides, the old OEM HT leads have been on the bike for 14 years!

Aprilia Caponord ETV1000 Rally-Raid Magnecor KV85 2530 part number ignition cable HT leadSo a couple of weeks ago I placed an order with Race Spec Performance (UK) for a set of Magnecor KV85 (Part No: 2530) HT leads. These are made on an order-by-order basis and this means a bit of a wait if lots of orders are flooding in as the riding season gets underway. They make it very clear that the wait could be three to four weeks. I wasn’t in a rush, the wait would be fine. So I was pleasantly surprised when they rocked up on the doorstep in just over two weeks – excellent stuff!

Aprilia Caponord ETV1000 Rally-Raid Magnecor KV85 2530 HT leads and sticker!Now these leads are designed to fit on the OEM Sagem/JCI coils but also fitted my modified HAAS coils with no issues at all. Well maybe one ……. the rubber boot is such a damn good fit it doesn’t allow the air out as the lead is pushed into place – so the trapped air just builds up pressure as the volume decreases. Then when you let go it oh-so gently pushes the lead back off again! The trick is to get it seated properly then slide something blunt up under the boot until hearing a ‘psstttt’ as the trapped air escapes …… NOW the lead is on securely!

Aprilia Caponord ETV1000 Rally-Raid Magnecor KV85 2530 HT lead on HAAS modified coilOverall the caps are shorter than the OEM angled ones and even with 8.5mm diameter cables the fit and bend of the supple cables is perfect in all four mounting locations. Overall length is fine allowing cables to be routed comfortably without trying to lose excess cable or bend cables in an unreasonably tight radius. And of course, now the engine looks way more powerful with these bright red babies in place!

Would I buy them again? Yes. I’ll definitely pop a set on the other Raid, with one proviso – I’ll skip the international shipping as it’s a bit steep (£16 versus £4.99 shipped within the UK). Otherwise at £50.99 I’m happy enough given the quality of the product, excellent fit and 10 year limited warranty. So lets start clocking up the mileage and how well they last!

 

Ognibene sprockets

The first Ognibene (7164-16) 16 tooth front sprocket was fitted last April, since then its done over 18,000 miles and I’m happy to say, still has some life left in it. In comparison to the excellent Renthal sprockets that I’d used since the OEM one wore out, I have to say I’m very impressed. Yes they cost a couple of pounds more that the Renthal, but it has covered more miles. The Reynolds typically averaged (15,000 miles), making the Ognibene’s running cost slightly better pence-per-mile wise.

Now a matching set of front and rear (8098-45) sprockets are going on, along with a nice new gold/gold DID 525-112 ZVM-X chain. Aprilia Caponord ETV1000 Rally-Raid Ognibene front sprocket 7164-16The France Equipment rear sprocket (1683-45) I fitted last year is still looking pretty good, so it’ll go on the shelf as a part-worn spare.

One thing that’s maybe worth mentioning about Ognibene sprockets is to be aware that the ‘silent’ bands will bed-in over the first few miles. Initially the chain side-plates ride up on the hard plastic bands before sinking in – changing the effective diameter of the chain’s run around the sprocket ……. this means your chain adjustment has to be monitored more carefully at the beginning Aprilia Caponord ETV1000 Rally-Raid Ognibene 8098-45 rear sprocket and DID ZVM-X chainand will no doubt require a couple of tweaks. Once everything beds-in I guess it’s business-as-usual with regards to the long intervals between adjustments that I like about the DID chain.

New chain and rear Ognibene sprocket courtesy of Motrag at a very competative price. Unfortunately they could only supply the 17 tooth front, not the 16 tooth…… that may change in time.

Cam chain tensioner – Part 3 ….. Judgment Day!

Aprilia Caponord ETV1000 Rally-Raid cam timing chain tensioner AP0236252 AP0236253A few days ago the two new cam (timing) chain tensioners (AP0236253) arrived ……. and as if she knew, the Capo started to rattle the rear cylinder for a second or two at almost every start-up! So as soon as we got home yesterday, it was off with the bike kit and into the workshop-wear and time to seriously twiddle some spanners.

Thankfully the rear tensioner is nice and easy. Fuel tank up, pop out a couple of spark plugs to make rotating the rear cylinder to top-dead-center nice and easy, then rummage under the wiring on the right hand side and find the cap requiring a 6mm hex-key.. Remove the cap and the copper washer underneath and then use something pointy to hook the tensioner out enough to get a grip with podgy fingers.

Aprilia Caponord ETV1000 Rally-Raid AP0236252 cam timing chain tensioner INA F-46807The tensioner shows definite signs of movement and rotation and the plunger could be pushed in about 1/2 its travel ….. I think FUBAR best describes it! The new tensioner was oiled up and before it was dropped into the motor I did a little experiment. Both old and new parts were flushed and filled with new 15w/50 and gently pinched in a vice. The new tensioner remained snug for a long time, only a small amount of oil could be seen coming out ….. next up the old one. This remained snug for no more than 1-2 minutes and oil could be seen leaking from it the second it was compressed. So all in all a major difference in performance between old and new.

Aprilia Caponord ETV1000 Rally-Raid cam timing chain tensioner AP0236252 AP0236253After a few more jobs were carried out, it was buttoned together and warmed up …. no rattles and in fact the idle was smoother than it has been in a while.

The tensioner that came out is an original Mk1 (AP0236252) that was superseded by the new version a good few years back. From what year they were fitted as standard I don’t know. Looking closely at the old one I found ‘INA F-46807’ printed around the edge. I can’t find much about it unfortunately. However ……..

……. I did find something that might be of interest. It looks like the tensioner fitted to the BMW 650 (late models) and F700/800 bikes could well be the same. Now this can only be corroborated by direct comparison, so I might tout the other new Aprilia one around a few BMW dealers to see if I can find out if they match. If they do fit, then they are available for substantialy less than the £68 each from Aprilia.

Keeping the postman busy

Aprilia Caponord ETV1000 RST Futura hybrid velocity stack 47mm 51mmAfter January’s awful weather – snow, rain, sub-zero temps, earthquakes & landslides, it’s been a very nice balmy February! So much so, that the Capo has squirreled a good few miles under its belt – the last 300 of them with the new snorkel in place. And I have to say, I’m really chuffed at how it performs. No extra induction noise that my aged arthritic lug holes can detect and no detriment to performance even though it’s been nowhere near a dyno to tweak the mapping.

Aprilia Caponord ETV1000 Rally-Raid cam chain tensioner AP0236253As I write, a swanky set of Futura throttle bodies are winging their way here, as are a nice new pair of Mk2 cam chain tensioners – AP0236253. The velocity stacks are now finished and ready to fit to the throttle bodies and so it just leaves the matter of swapping out the Anakee Wild tyres for a fresh set of Anakee 3’s and a DID ZVM-X chain and Ognibene front/rear sprocket set (courtesy of Motrag) and I think she’ll be ready for a damn good thrashing on Dr Dyno! 🙂

 

Take a deep breath ……..

Hawker Typhoon air inlet and radiatorWith plans a-foot to assemble a big-cc motor for the Capo, it was time to cast an inquisitive eye over the airbox snorkel, that ugly rubber protrusion at the front of the airbox, sucking in hot air from on top of the radiator. This one object has been debated far and wide over the years – keep it, or remove it? Yes the questionable snorkelectomy!

Only a couple of ways to find out I guess. Dyno the bike with and without it or draw it up and run a flow analysis on it from the comfort of an armchair. Armchair it is then! With the model Aprilia Caponord ETV1000 Rally-Raid snorkel restrictioncomplete, here’s a couple of basic facts: Snorkel Inlet area (total) 1,750mm² and outlet area (total) 3,050mm². So the inlet is slightly restricted, the offending area is highlighted in the picture (click to enlarge). In fact, if the restriction were removed, the snorkel would have an inlet nearer to 2,400mm² – about 37% more!

To keep it simple the analysis was run with air at 1013mb and 20C, both with AND without the Aprilia Caponord ETV1000 Rally-Raid airbox snorkel air velocity and pressurerestriction in place and at RPM’s ranging from 1,300 to 10,250 – well above Caponord max RPM of 8,750.

I think it’s reasonable to say that the OEM snorkel doesn’t really do badly until it hits 9,000RPM+ and lets face it, by then the whole thing is over for the poor old Capo anyway! Based on a days digital twiddling and some airbox datalogging several years ago, I have to say that I’m planting my flag firmly in the ‘leave it alone’ camp when it comes to the OEM Capo snorkel. It isn’t and never will be an RSV so why try to make it like one ….. the standard bits are designed to work well enough together for the style of bike it is. Yes of course remapping will improve things no end, but why screw up the ride by making it noisier and offering the local mice a HUGE entrance through which to set up an epic knocking shop on Aprilia Caponord ETV1000 Rally-Raid airbox snorkel air pressure & velocitythe air filter!

But what about the big-cc conversion? well running the analysis with the 1,103cc and 1,127cc flow certainly seemed to cast doubt on the suitability of the OEM snorkel as the strong pressure drop is now occurring lower down the rev range. So the snorkel design originally drawn up back in October 2012 was dug out of hibernation, modified and polished up for 3D printing and run through the flow software – the green line on the graph above. Overall it seems to offer a cleaner flow, less pressure drop and maintains a similar airflow velocity into the airbox. Unfortunately the one thing the software can’t tell me is how much extra Aprilia Caponord ETV1000 Rally-Raid airbox snorkel 3D print printednoise will be generated! The OEM snorkel is made of PVCD (flexible) AND has a foam pad in the roof of each inlet – both presumably are to reduce inlet noise.

With everything looking OK a few test parts were printed to make sure it’s going to fit, then the model was split into two along the mounting plate and both parts printed separately. This was due both to size limitations in the printer and because I didn’t want to use any support material to upset the surface finish. Afterwards both parts were bonded together and the inlet tracts rubbed down with 80/180/400/1200 grit sandpaper to get a reasonable finish.

Aprilia Caponord ETV1000 Rally-Raid acoustic panel AP8117151With a bead of sealant and 4x M4x12 and 4x M5x12 screws and nyloc-nuts, the snorkel fits into place just fine. Of course only time will tell how well it stands up to the rigours of its new home! The OEM snorkel has a rubber/foam acoustic panel (AP8117151) that fits over it and of course it won’t fit the new one, so I’ve trimmed this one to suit(ish) and placed an order for a similar dual-material sound deadening product to make a new one specifically for this snorkel. However the chopped-about old panel can’t be far off the ball park, as inlet noise just wasn’t noticeable which was a pleasant surprise …… It could well be a different story from the saddle though! 🙄 

So what next? Well the plan is to get a day on a dyno when the weather is more amenable. I’d like to run it as standard, standard + new snorkel and Futura throttle bodies, new velocity stacks and new snorkel and see what the numbers say. Any guesses?

Airbox crankcase vent – Mk2

Aprilia Caponord ETV1000 Rally-Raid engine crankcase vent pipe to airbox and throttle body

With the velocity stacks and snorkel measured up and squirreled away in CAD, it was time to rebuild the airbox …… except billy-butter-fingers here, went and knocked the airbox base off a chair onto the floor – not far – but enough for it to land awkward and break the spigot for the crankcase vent. Unfortunately the spare I’d made, I gave away to a friend last year! So there I am trying to remember where I’d bought the bits to make Aprilia Caponord ETV1000 Rally-Raid engine crankcase vent flow analysisanother one, when I had a “Stop the bus!” moment …… don’t waste time and fuel going into town, sit down, draw something in CAD and print that puppy! 😀 

Here’s the finished article …. it has a slightly larger inlet/outlet cross-section, although the previous one worked just fine and this time the fit for the grey pipe is better. internally there is a chamber to help reduce gas flow and (hopefully) convince some of the oil to condense and run back down into the crankcase, not out into the airbox. That’s the theory anyway, but it’ll probably turn out to be complete bollocks! Either way, it looks neater so that’s a positive step forward ……. now, what else can I break today! 😀

Aprilia Caponord ETV1000 Rallyb-Raid engine crankcase airbox vent 3D print

The MK1 vent did well and lasted almost  2 years (37K miles) and in that time I never had a moments issue with oil in the airbox going where it shouldn’t. Let’s hope this one does as well!

 

Hybrid velocity stacks

Aprilia Caponord ETV1000 Rally-Raid 47mm and hybrid 51mm velocity stacksIf all goes to plan, later this year the second Rally-Raid that’s currently being rebuilt, will finally get a motor installed. The plan is to use a big-bore motor …. an 1,103cc in place of the standard 998cc. The compression and valve timing will remain bog-standard Caponord (10.5/1  Inlet timing – 25°BTDC/37°ABDC and Exhaust timing – 57°BBDC/5°ATDC). However to accommodate the increase in air-flow, I’ve decided to use Futura 51mm throttle bodies instead of the Caponord 47mm items.

Meanwhile on top of this chunky aluminium marvel sits a pair of velocity stacks. These stacks vary in height (and diameter) depending on the intended tune of the engine. The RSV Mille of course is designed as a race-rep and as such wants high horsepower at high RPM – hence 57mm throttle bodies and very short velocity stacks. On the other hand the Caponord was tuned for improved low-end grunt and so has small throttle bodies (47mm) and tall velocity stacks to maintain good gas flow speed at low RPM. The Futura seems to sit firmly between the two!

Now of course I could simply use the medium height velocity stacks straight off a Futura, but I decided to go a different route and print a new pair of hybrid stacks – Caponord height BUT 51mm diameter to fit the Futura throttle bodies. Unlike ABS, Colorfabb Ngen (Co-Polyester) can’t be vapour polished with Acetone, so I’ll have to sand the venturi down with a variety of grades of wet-and-dry up to 2,000 grit and maybe finish it off with something like Quixx plastic polish – if it works on this stuff! Here’s a couple of pics comparing the original and new version – straight out of the printer!

Unfortunately 3D parts (unless made on high-end machines) don’t typically have the same strength as injection molded or machined parts – but they do make great ‘proof-of-concept’ parts! If these stacks prove to be a positive step forward, but not durable enough for the working environment, I can at least get the drawings to the machine shop and have them made in aluminium … but that’ll be a tad more expensive than 85p each off the printer! 🙁 

UPDATE

Just had a spare half-hour to rub some 100/400 & 1200 grit paper down one of the stacks and all I can say is – WOW! This material rubs up lovely and probably a couple more sessions will see it through. All the print-ridges have gone and I can’t feel anything but a nice smooth surface that retains a print pattern that makes it look quite distinctive.  🙂

Aprilia Caponord ETV1000 RST1000 Futura Rally-Raid hybrid velocity stack

 

 

Murphy’s law working as well as ever!

Aprilia Caponord ETV1000 Rally-Raid and RST Futura Sagem or JCI Ignition coilsYes I put my hand up …… it was all my own fault! I just had to go and mention the Sagem coils in the last post. A real tweak on the nose of Murphy’s Law if ever there was one!

The other day I had to pop along to the shops and being a lovely warm sunny day it was definitely a job for the Capo, besides I had the Innovv K1 camera system fitted and this would be an ideal time to try it out. The first sign that something was amiss with the Capo was a slight hesitation, a stumble just off idle. That and a slight misfire occasionally – more a sensation through the seat than anything else.

arcOnce back in the barn I had a look at the Innovv DV recorder – No stored video, nothing! What the hell? Then the penny dropped ….. The Innovv worked fine with the engine off, but fire it up and it had a complete meltdown and either turned off or froze. It looks like some serious interference at work. With the seats off, I realised there was a faint intermittent ‘tick, tick, tick’ to be heard over the exhausts from the battery/coil area but I couldn’t see anything. So I waited until dusk and tried again – bingo! – A nice intermittent flash of HT from a rear coil to the subframe. That’ll most certainly mess things up quite nicely.

With one Sagem definitely now duff I decided to retire both remaining ones. After all, 111,000 miles isn’t too shabby! To keep all coils the same I thought I’d order three TechAutos – two as replacements to match the two already installed and one as a spare, just in case. So back indoors, fire up Flea-Bay and almost fall off my chair when I see what TechAutos are up to! Here’s a screenshot of their latest pricing for 3x coils. Hmmm……

techauto-1

…… So I fired off an email asking about availability and real-world prices – and after four days, never heard back from them. I decided that with outstanding customers service such as that, I would go elsewhere and buy Renault V6 coils! In fact for the last realistic price I recall seeing for three TechAutos coils I can buy six Renault coils. Now the old girl will get a nice new full set of coils and HT leads plus a new set of Iridium plugs ….. hopefully that’ll keep her happy for a few thousand miles!

Review – Motrag ETV1000 radiator protection

Aprilia Caponord ETV1000 Rally-Raid Motrag radiator protection/guardYesterday a whopping 15Kg parcel of goodies from Manuel at Motrag turned up. Although the box was bursting with new toys, I just focused on the one part I’d really been waiting for – the lovely stainless-steel radiator guard. I know Motrag have had lots of interest in this, which stands to reason with the Touratech guard no longer available. The only other alternative seems to be one from Ebay that could easily be copied for an awful lot less money – after all, it’s only aluminium mesh with a rubber strip and held on by zip-ties.

This guard is made from glass-shot V4A stainless-steel (equivalent SAE316 for harsh environments) with powder coated aluminium mesh bonded to the frame and weighs in at approx 750g. It is held in place by two Scotch ‘Dual Lock’ adhesive fasteners at the top of the radiator and the two fastening points that the ‘cooler spoiler’ (AP8139628) mounts to at the bottom.

Installing the guard is very straight forward …. remove the crash bars & cross brace (if you have them), side panels and spoiler panel. I also removed the tank while servicing the bike which does make access even easier, but isn’t strictly necessary. Give the radiator a good clean and take a few Aprilia Caponord ETV1000 Rally-Raid Motrag radiator protection/guard & fog lamp bracketsminutes to carefully bend back any fins that have been damaged by stones or jay-walking deer. Then clean and thoroughly de-grease the top of the radiator on both sides. The guard has about 1-1.5mm clearance either side when in position – I used a couple of split pins as spacers to make sure the guard was nicely positioned. Do a dry run so you get it located just right and then when you’re happy – whip off the adhesive pad protection and fit the guard for real.

Next up, I had to bond a couple of spacers onto the clips where the spoiler/guard mount –  these take up the space between clip and the new guard. They can’t really be fitted when reassembling the spoiler as access is difficult – hence bonding them onto the clip first. Motrag will be supplying the adhesive in the kit! I gave it 1/2hr to dry, then began the rebuild – crash bar cross-brace, tank, panels, spoiler and finally the crash bars themselves ….. another 20 mins tops.

So, the verdict. Easy to fit with no modifications required. The fit is superb and the stainless frame is nice and stiff, so no worries about vibration induced scuffing of the radiator. As always, the Motrag attention to detail – fasteners and instructions is 100%. If there iAprilia Caponord ETV1000 Rally-Raid Motrag radiator protection/guard & fog lamp bracketss a negative anywhere to be found, then some may question the weight … to me the Capo is a big old lump anyway, a few extra grams won’t snap the frame!

Of course aesthetics are a personal matter, but to me it looks good and is definitely in keeping with the spirit of the Rally-Raid. That just about covers fit and form, but what about function? Well I admit I’ve yet to turn a wheel with the guard in place, but I know Motrag put plenty of miles on a pre-production one and had no problems, so I’m confident it’ll work just fine. But just to be sure, I’ll post again in a few weeks when the Capo has another 3-4K miles on it.

These guards are on sale now over at motrag.com for €64.95 including tax. That’s about half the price of the Touratech guard before it disappeared off the website!